Comparison of Legal Requirements: The Machinery Directive vs. the Machinery Regulation
1.7.4.2. Contents of the instructions (for use)
Changes
- The requirements for the contents of the instructions are extended to include new provisions for digital access to the EU Declaration of Conformity, as well as additional requirements regarding rescue information and data on emissions of hazardous substances.
- The requirement for an EC Declaration of Conformity is replaced by the EU Declaration of Conformity. Pursuant to Article 10(8), the manufacturer may also provide an internet address or machine-readable code, such as a QR code, where the declaration can be accessed.
Article 10(8)
Manufacturers shall ensure that the machinery or related product is accompanied by the EU declaration of conformity set out in Annex V, Part A or, alternatively, manufacturers shall provide the internet address or machine-readable code where that EU declaration of conformity can be accessed in the instructions for use and the information set out in Annex III.
Digital EU declarations of conformity shall be made accessible online for the expected lifetime of the machinery or related product and in any event for at least 10 years after the placing on the market or the putting into service of the machinery or related product.
- New requirement: Digital EU Declarations of Conformity must remain accessible online for the expected lifetime of the product and for at least 10 years following placing on the market or putting into service.
- The requirements for information on airborne noise emissions are clarified to encompass common specifications adopted by the Commission pursuant to Article 20(3), in addition to harmonised standards.
Article 20(3)
The Commission may adopt implementing acts establishing common specifications covering technical requirements that provide a means to comply with the essential health and safety requirements set out in Annex III for products within the scope of this Regulation.
Those implementing acts shall only be adopted where the following conditions are fulfilled:
(a) the Commission has requested, pursuant to Article 10(1) of Regulation (EU) No 1025/2012, one or more European standardisation organisations to draft a harmonised standard for the essential health and safety requirements set out in Annex III and:
(i) the request has not been accepted; or
(ii) the harmonised standards addressing that request are not delivered within the deadline set in accordance with Article 10(1) of Regulation (EU) No 1025/2012; or
(iii) the harmonised standards do not comply with the request; and
(b) no reference to harmonised standards covering the relevant essential health and safety requirements set out in Annex III has been published in the Official Journal of the European Union in accordance with Regulation (EU) No 1025/2012 and no such reference is expected to be published within a reasonable period.
Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 48(3).
- The provision on airborne noise is supplemented with an explicit reference to the correct assembly and installation of noise-reducing machinery or related products, where applicable.
- The term "Community Directives" is replaced with "specific Union legal acts" in the provision regarding noise measurement.
- New requirement: Where applicable, the instructions must include information on necessary precautions, devices, and means for the prompt and gentle rescue of persons.
- New requirement: Where the design of the machinery or related product allows for emissions of hazardous substances, the instructions must specify particular data in accordance with point 1.7.4.2(x).
- The information concerning hazardous substances must include at least one of the following: the emission flow rate, the concentration of hazardous substances around the machinery, or the effectiveness of the collection or filtration device and the conditions for maintaining it.
- If a collection, filtration, or exhaust system is not supplied with the machinery, the instructions must also specify the characteristics of the system in accordance with the provision.
- The values for hazardous substances must be based on measurements taken from the actual machinery or a technically comparable machinery or related product representative of the state of the art.
Proposed measures
-Update the table of contents and verification points of the instructions in accordance with Annex III, point 1.7.4.2.
-Ensure that the EU Declaration of Conformity accompanies the machinery, or that the instructions and information set out in Annex III contain an internet address or machine-readable code where the declaration can be accessed.
-If the EU Declaration of Conformity is provided in digital format, ensure that it remains accessible online for the expected lifetime of the product and for at least 10 years following placing on the market or putting into service.
-Verify that references to applicable harmonised standards or common specifications are correct and up to date.
-Ensure that airborne noise emissions are measured and reported in compliance with applicable requirements, including test codes, operating conditions, and measurement uncertainty.
-For noise-reducing machinery or related products, assess whether the instructions must include specific provisions for proper assembly and installation.
-Determine potential situations requiring immediate rescue of persons and specify the relevant precautions, devices, and equipment in the instructions.
-Identify whether the machinery or related product may emit hazardous substances during intended use.
-Where emissions of hazardous substances are possible, determine the data to be provided pursuant to point 1.7.4.2 (x), such as flow rate, concentration, or collection and filtration efficiency.
-Where necessary containment, filtration, or evacuation equipment is not supplied with the machinery, ensure that its relevant characteristics are specified in the instructions.
-Verify that declared emission values are based on actual measurements or on relevant measurements of technically comparable machinery or related products.
-Ensure that the operating conditions required to maintain the efficiency of containment or filtration equipment are specified where such data is referenced.
-Verify that the content of the instructions corresponds to the actual machinery design, risk assessment, and operating conditions.
Machinery Directive statutory text
1.7.4.2. Contents of the instructions
Each instruction manual must contain, where applicable, at least the following information:
(a) the business name and full address of the manufacturer and of his authorised representative;
(b) the designation of the machinery as marked on the machinery itself, except for the serial number (see section 1.7.3);
(c) the EC declaration of conformity, or a document setting out the contents of the EC declaration of conformity, showing the particulars of the machinery, not necessarily including the serial number and the signature;
(d) a general description of the machinery;
(e) the drawings, diagrams, descriptions and explanations necessary for the use, maintenance and repair of the machinery and for checking its correct functioning;
(f) a description of the workstation(s) likely to be occupied by operators;
(g) a description of the intended use of the machinery;
(h) warnings concerning ways in which the machinery must not be used that experience has shown might occur;
(i) assembly, installation and connection instructions, including drawings, diagrams and the means of attachment and the designation of the chassis or installation on which the machinery is to be mounted;
(j) instructions relating to installation and assembly for reducing noise or vibration;
(k) instructions for the putting into service and use of the machinery and, if necessary, instructions for the training of operators;
(l) information about the residual risks that remain despite the inherent safe design measures, safeguarding and complementary protective measures adopted;
(m) instructions on the protective measures to be taken by the user, including, where appropriate, the personal protective equipment to be provided;
(n) the essential characteristics of tools which may be fitted to the machinery;
(o) the conditions in which the machinery meets the requirement of stability during use, transportation, assembly, dismantling when out of service, testing or foreseeable breakdowns;
(p) instructions with a view to ensuring that transport, handling and storage operations can be made safely, giving the mass of the machinery and of its various parts where these are regularly to be transported separately;
(q) the operating method to be followed in the event of accident or breakdown; if a blockage is likely to occur, the operating method to be followed so as to enable the equipment to be safely unblocked;
(r) the description of the adjustment and maintenance operations that should be carried out by the user and the preventive maintenance measures that should be observed;
(s) instructions designed to enable adjustment and maintenance to be carried out safely, including the protective measures that should be taken during these operations;
(t) the specifications of the spare parts to be used, when these affect the health and safety of operators;
(u) the following information on airborne noise emissions:
— the A-weighted emission sound pressure level at workstations, where this exceeds 70 dB(A); where this level does not exceed 70 dB(A), this fact must be indicated,
— the peak C-weighted instantaneous sound pressure value at workstations, where this exceeds 63 Pa (130 dB in relation to 20 μPa),
— the A-weighted sound power level emitted by the machinery, where the A-weighted emission sound pressure level at workstations exceeds 80 dB(A).
These values must be either those actually measured for the machinery in question or those established on the basis of measurements taken for technically comparable machinery which is representative of the machinery to be produced.
In the case of very large machinery, instead of the A-weighted sound power level, the A-weighted emission sound pressure levels at specified positions around the machinery may be indicated.
Where the harmonised standards are not applied, sound levels must be measured using the most appropriate method for the machinery. Whenever sound emission values are indicated the uncertainties surrounding these values must be specified. The operating conditions of the machinery during measurement and the measuring methods used must be described.
Where the workstation(s) are undefined or cannot be defined, A-weighted sound pressure levels must be measured at a distance of 1 metre from the surface of the machinery and at a height of 1,6 metres from the floor or access platform. The position and value of the maximum sound pressure must be indicated.
Where specific Community Directives lay down other requirements for the measurement of sound pressure levels or sound power levels, those Directives must be applied and the corresponding provisions of this section shall not apply;
(v) where machinery is likely to emit non-ionising radiation which may cause harm to persons, in particular persons with active or non-active implantable medical devices, information concerning the radiation emitted for the operator and exposed persons.
Read more
Machinery Regulation legal text
1.7.4.2. Contents of the instructions for use
Instructions for use shall contain, where applicable, at least the following information:
(a) the business name and full address of the manufacturer and, where applicable, of its authorised representative;
(b) the designation of the machinery or related product as marked on the machinery or related product itself, except for the serial number (see section 1.7.3);
(c) the EU declaration of conformity, or the internet address or machine readable code, where the EU declaration of conformity can be accessed, in accordance with Article 10(8);
(d) a general description of the machinery or related product;
(e) the drawings, diagrams, descriptions and explanations necessary for the use, maintenance and repair of the machinery or related product and for checking its correct functioning;
(f) a description of the workstation(s) likely to be occupied by operators;
(g) a description of the intended use of the machinery or related product;
(h) warnings concerning the ways in which the machinery or related product must not be used that experience has shown might occur;
(i) assembly, installation and connection instructions, including drawings, diagrams and the means of attachment and the designation of the chassis or installation on which the machinery or related product is to be mounted;
(j) instructions relating to installation and assembly for reducing noise or vibration;
(k) instructions for the putting into service and use of the machinery or related product and, if necessary, instructions for the training of operators;
(l) information about the residual risks that remain despite the inherent safe design measures, safeguarding and complementary protective measures adopted;
(m) instructions on the protective measures to be taken by the user, including, where appropriate, the personal protective equipment to be provided;
(n) the essential characteristics of tools, which may be fitted to the machinery or related product;
(o) the conditions in which the machinery or related product meets the requirement of stability during use, transportation, assembly, dismantling when out of service, testing or foreseeable breakdowns;
(p) instructions with a view to ensuring that transport, handling and storage operations can be made safely, giving the mass of the machinery or related product and of its various parts where these are regularly to be transported separately;
(q) the operating method to be followed in the event of accident or breakdown; if a blockage is likely to occur, the operating method to be followed so as to enable the equipment to be safely unblocked;
(r) the description of the adjustment and maintenance operations that should be carried out by the user and the preventive maintenance measures that should be observed taking account of the design and the use of the machinery or related product;
(s) instructions designed to enable adjustment and maintenance to be carried out safely, including the protective measures that should be taken during these operations;
(t) the specifications of the spare parts to be used, when these affect the health and safety of operators;
(u) the following information on airborne noise emissions:
(i) the A-weighted emission sound pressure level at workstations, where this exceeds 70 dB (A); where this level does not exceed 70 dB (A), this fact shall be indicated;
(ii) the peak C-weighted instantaneous sound pressure value at workstations, where this exceeds 63 Pa (130 dB in relation to 20 μPa);
(iii) the A-weighted sound power level emitted by the machinery or related product, where the A-weighted emission sound pressure level at workstations exceeds 80 dB (A).
These values shall be either those actually measured for the machinery or related product in question or those established on the basis of measurements taken for technically comparable machinery or for a technically comparable related product, which is representative of the machinery or related product to be produced.
In the case of very large machinery or a related product, instead of the A-weighted sound power level, the A-weighted emission sound pressure levels at specified positions around the machinery or related product may be indicated.
Where the harmonised standards or common specifications adopted by the Commission in accordance with Article 20(3) cannot be applied, sound levels shall be measured using the most appropriate method for the machinery or related product.
Whenever sound emission values are indicated, the uncertainties surrounding these values shall be specified. The operating conditions of the machinery or related product during measurement and the measuring methods used shall be described.
Where the workstation(s) are undefined or cannot be defined, A-weighted sound pressure levels shall be measured at a distance of 1 m from the surface of the machinery or related product and at a height of 1,6 m from the floor or access platform. The position and value of the maximum sound pressure shall be indicated.
With respect to noise reduction machinery or related products, the instructions for use shall specify, where appropriate, how to correctly assemble and install that equipment (see also section 1.7.4.2(1), point (j)).
Where specific Union legal acts lay down other requirements for the measurement of sound pressure levels or sound power levels, those legal acts shall be applied and the corresponding provisions of this section shall not apply;
(v) information on the necessary precautions, devices and means for the immediate and gentle rescue of persons;
(w) where machinery or related products are likely to emit non-ionising radiation, which may cause harm to persons, in particular persons with active or non-active implantable medical devices, information concerning the radiation emitted for the operator and exposed persons;
(x) where the design of machinery or related products allows emissions of hazardous substances from the machinery or related product, the characteristics of the capturing, filtration or discharge device if such device is not provided with the machinery or related product, and any of the following:
(i) the flow rate for the emission of hazardous materials and substances from the machinery or related product;
(ii) the concentration of hazardous materials or substances around the machinery or related product coming from the machinery or related product or from materials or substances used with the machinery or related product;
(iii) the effectiveness of the capturing or filtration device and the conditions to be observed to maintain its effectiveness over time.
The values referred to in the first subparagraph shall either be actually measured for the machinery or related product in question or established based on measurements in respect of technically comparable machinery or a technically comparable related product, which is representative of the state of the art.
Read more
Do you have any questions? Contact us